EPDM Sheet Rubber
Excellent general-purpose gasket materials for air, hot and cold water, saturated stream, and exterior service. EPDM sheets provide outstanding resistance to weathering, ozone, and UV exposure along with chemical resistance and dynamic properties.
We carry EPDM in the following:
- Thickness: 1/8″ to 3/8″
- Roll width: 36″
Neoprene Sheet
This blended neoprene sheet is used where good oil, petroleum, ozone, and weathering-resistance is needed. It is very popular due to the broad range of applications in which it may be used. Neoprene sheets are good for uses such as bumpers, pads and in sealings and gaskets.
We carry Neoprene in the following:
- Thickness: 1/16″ to 1″
- Roll width: 36″ or 48″
Neoprene Diaphragm Rubber
Each of these diaphragm sheets is manufactured with a high-quality compound designed for long service. Each is reinforced with high-quality, square-woven duck to provide balanced structural strength over the entire area of the diaphragm. Recommended for control valves, regulators, and pumps, they also make excellent weather strip materials.
We carry Diaphragm in the following:
- Thickness: 1/16″ to 3/32″
- Roll width: 56″
Commercial Grade Neoprene Rubber
These products are blends of neoprene, nitrile and SBR rubbers. They are moderately oil-resistant, for use as bumpers, pads and in sealing and general gasket applications. These are commercial grade materials, not recommended in applications where high oil resistance is required. For low-line pressure applications such as air, hot and cold water, saturated steam and low-pressure steam.
Nitrile Sheet
Nitrile sheet is primarily used for applications where resistance to oil, solvents and fuels is required. GRT Rubber offers several styles of nitrile sheets, including a white nitrile made with FDA-approved ingredients.
We carry Nitrile in the following:
- Thickness: 1/8″ to 3/8″
- Roll width: 36″
Chute Lining & Skirtboard
- GRT Chute Linings and Skirtboard are designed to be an integral part of a conveyor system.
- Chute lining protects and cushions the chute from the material being handled; Skirtboard prevents fugitive materials from escaping and damaging the conveyor loading areas.
- We carry Chute in the following:
- Thickness: 1/8″ to 1/2″
- Roll width: 48″
Pure Gum Tan Rubber
- Highest tensile strength, pure gum rubber is used for skirt boards, bumper stock. Laundry lining, sand and shot blast curtains, scraper stock and tumbler liners.
- We carry Pure Gum Tan in the following:
- Thickness: 1/16″ to 3/4″
- Roll width: 36″
Viton Rubber
- Excellent resistance to heat and oil combinations: hot greases found in engines and compressors.
- Excellent resistance to a wide range of concentrated chemicals and acids.
- We carry Viton in the following:
- Thickness: 1/32″ to 3/8″
- Roll width: 36″
Silicone Rubber
- Weathering resistance—resists sunlight, ozone, and gases
- Good fungus resistance
- Resistance to water—silicone resists the deteriorating effects of agents found in rainwater and surface water
- Able to withstand temperatures of up to 450 degrees.
- We carry Silicone in the following:
- Thickness: 1/32″ to 1/2″
- Roll width: 36″
Linatex Rubber
- Linatex® premium rubber exhibits outstanding strength, resilience and resistance to cutting and tearing, giving superior performance in wet abrasion conditions.
- Offers extended wear life and unmatched wear performance in even the harshest of environments.
- In addition to mining and aggregate applications, Linatex® rubber is used across a variety of other industries including floor care, belting and target backing.
- We carry Linatex in the following:
- Thickness: 1/16″ to 3/4″
- Roll width: 36″
Red Sheet Rubber
- A cloth finish, drum cured Natural SBR rubber is an excellent, low cost, flange gasket material.
- Temperature rating of -20 to 180 degrees F.
- We carry Red Sheet in the following:
- Thickness: 1/16″ to 1/8″
- Roll width: 36″